• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Fitting a cat flap can seem intimidating however it's actually quite simple with the proper instructions. Find out how much to install a cat flap high you'd like the flap to be (normally it's located at the belly height). Note this on the door, and use the template included as a guide to drill.

If you have a young kitten you can prop the door open very slightly and gradually allow it to enter. Reward the kitten every time it passes.

Take a measurement of the door

A cat flap is a great way to let your pet come and go in and out of your home as it likes. This can help with keeping your cat healthy by making sure that it is getting exercise and also being able to get back in if stuck outside in bad weather, especially during the winter. It also can reduce the amount of time you have to let it in or out and can also keep your home safe by letting you know when it has gone out.

It is essential to make sure that the cat flap is placed correctly to stop your pet from being forced through through it by other animals (e.g. dogs). It is important to measure the height of your pet's belly and the doorway to your home in order to make sure that the flap is at the correct height. You can alter the height of your flap when your cat is taller or less than the average.

The next step is to use a spirit level to mark the center of the door. This is where you will install the flap. Then, using the marks as an outline, cut the shape of the flap using the help of a jigsaw. After you have cut the flap then sand the edges to create smooth surfaces. Drill any necessary holes.

The process of installing the cat flap isn't as difficult as you may believe and it shouldn't take more than two hours for the entire process from beginning to finish. However, the process can be a little more complicated when you have to install it onto the door of a uPVC or composite door because these doors have various thicknesses which can affect how the holes are cut and the type of door they are fixed into. This is why we recommend hiring an expert to do the job, particularly if you have never worked with glass before.

Measure Your Cat

You will not have to spend hours of listening to the pet meow to be allowed in or out. This is especially helpful for those who working all day and your cat has to stay inside waiting until you get home in any weather.

If you're planning to put a cat flap inside your door, it is crucial that you determine the size of your cat prior to beginning the task. Although it might seem like a simple operation it is important to make sure you measure correctly or your pet will be unable to use.

First of all, make sure that your cat flap in upvc door panel is relaxed and not stressed before you take the measurements. You'll need to keep them in a way that they are not able to move, and make sure that the ruler or measuring tape is flat against their body and not arching in any places. You can take a precise measurement by keeping the measuring tape or ruler flat against the body of the animal from the top to the bottom.

Once you've figured out the measurements of your cat, it's time to take a look at the door and decide on where to place the flap. It is advisable to position the flap in the middle of your cat's stomach as this will allow them to pass through it with minimal effort. This will also stop the flap from making a lot of noise as it swings back and forth.

You must consider the thickness of the uPVC or composite door as well. While all doors made of timber have a similar thickness, uPVC or composite door cat flap doors can differ greatly in their overall structure. This can make the process of putting in an enclosure for your cat more difficult since you must ensure that the hole is the proper size.

You can also use the template drawing included in the instructions to mark the location of the hole on the door. This will enable you to determine where the hole must be located and ensure that the template is placed properly on the door. It is also beneficial to use a spirit-level to ensure that the template is flush against the door.

Cut the Flap

You'll need to make an opening in the door panel to install your cat flap prior to you can put it in place. This is a difficult task and it is recommended that you seek out the assistance of a professional cat flap fitting service to complete this task should you not have the knowledge or skills to tackle it yourself. It is also recommended to review the directions that come with the kit to learn how to do this correctly.

To do this, you have to take a measurement of the height of your cat's or kitten's belly and use that as an indication point. In general, place the cat flap approximately 10-15 centimeters above the ground. This is the typical height of the cat's belly. Your cat can move through the flap with ease and will also make the other cats or neighbours who are snooping a tough time trying to leave or enter.

Draw the location of the cat flap on the door with a pencil. If your kit has an outline put it on top of the door. Utilize the markings on the template to drill holes at each corner. Then, you should be able to cut the template shape and replace it with the flap for cats.

You can install your cat flap yourself in an uPVC or wood door if you are confident with the use of a jigsaw. Make sure you don't cut through any of the door's mullions, or vertical rails. You can use a Jigsaw to cut your panel into a circle or square according to the way you'd like it. Make sure to take your time and don't try to force the jigsaw to cut faster.

Once the hole has been cut, carefully place the cat flap in its new home. Make sure it is firmly secured. If the flap has screw caps then push them into the protruding bolts. After the screws are installed then sand the rough edges and seal any gaps. This will stop the entry of draughts into your home.

Fit the Flap

If you have an ordinary cat flap, you can help your pet to use it by placing a small amount cat food on the front of the door. Alternately, you can push the cat through using your hands or a stick. Once your cat is comfortable moving through the flap, it will be able to come and go whenever it wants. This lets you let it in and out at any time it wishes.

You can install the flap onto an UPVC or glass door although this may not be exactly the same as fitting one into a timber external door since the UPVC and glass doors don't have the same thickness. This can have a major impact on how you cut the flap's hole and whether the flap will fit correctly after installation.

The mounting kit may include a template showing you the best places to drill holes. If the kit doesn't include a template you can copy it to make your own. It's important to not use the jigsaw to hard when cutting, so that it doesn't leave a bigger than needed hole in your door.

Most cat flaps are square or rectangular in shape but there are also some which are circular and these are typically more difficult to place. If you have a circular flap it's essential to make sure the hole is in the proper location on your door as if it's not, the cat won't be able to use it and could be stranded out in the sun all day (or even at night).

Certain cat flaps have locks that allow you to regulate when your cat enters and leaves. These are very helpful if you're worried about your cat flaps for french doors going out at night and then coming back in due to the darkness, or if you're at work all day. Certain locks can be used to lock entrance or exit, while others can be locked in both directions. This is useful for sick or elderly cats who aren't keen to venture out in cold weather.