• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Replacing uPVC Window Handles

Switching the handles of windows made of upvc is a fairly straightforward task. The most important thing is to make sure that the replacement handle fits the spindle that was cut out of the window mechanism.

If you follow the steps below the handle of any cockspur will fit in most windows. The height of the step of the handle is key.

What to Look For

Over time, uPVC handles on many windows in the UK can start to show signs of wear and tear. If this occurs, the handle could become shaky or difficult to operate, making it necessary to replace it. Anyone who is familiar working with basic hand tools can accomplish this fairly simple job.

The first step is to make sure the handle is firmly connected to the window frame, and is in an open position. The next step is to locate the screws or pins that secure the handle. They are usually on the inside face of the handle and can be removed with a screwdriver, or pliers.

Once the handle has become loose, it can be removed from its hinges by gently pulling off. The next step is to find a replacement handle that is the same design and size. This can be done on the internet or in a local DIY store, and it should take five minutes using the help of a screwdriver.

The most important thing to consider when replacing a uPVC window handle is the step height. This is the distance from the base of the handle until it sits on the frame of the window. This is a common measurement and you should check the step height before ordering a replacement handle.

There are a variety of sizes based on the type of handle. Inline handles for uPVC windows typically feature lug centers of 31mm, and there are also handles with cockspur with 43mm centres. Tilt and turn handles are typically found on windows made of uPVC and they feature a specific design that allows the window to be slid up for ventilation and turned to open the window completely.

The most frequent breakage in uPVC handles is that they crack inside instead of breaking away from the base section. This can make them hard to open, and it is therefore essential to ensure that any replacement handle you buy has the same spindle length that your current one.

Remove the Old Handle

If your window handles are damaged or not properly installed, they could cause double-glazed windows to open and close incorrectly. They could even become stuck. There are a variety of reasons like general wear and tear or the corrosion of the handle made of metal. In these cases it is essential to replace the upvc window handle as promptly as you can to avoid further damage or loss of function.

One of the first steps that you should do when replacing window handles made of upvc is to remove the old handle from the window. To do this, start by getting rid of the screw that is covered when the handle is in the closed position. After you have removed the screw, you can remove the handle. It is a good idea to make use of an electric screwdriver for this as it will make the task much easier and quicker.

It is also worth noting that the screws on the handle may be hidden behind caps made of plastic, so it is a good idea to take an Stanley knife to the screw caps and then remove them. After you have removed the old upvc window handles handle, you will have to examine the square cutout on the base to make sure that the new handle for the window lock is compatible. This is important as you will need to measure the length of the spindle on the previous handle to ensure that it is the same size as the window mechanism and the handle spindle that has been cut out.

The different kinds of window handles made from upvc include: Espag handles, which have a central screw and can turn left or right; Cranked handles that have two screws and are used on tilt and turn upvc windows; and Spade handles, with an arm with a flat surface and can be placed on either side of the window. Once you have found a suitable replacement, it's simply a case of screwing the handle into place and ensuring that the spindle is inserted into the lock mechanism. Once this is done then it is time to secure it to the window frame and the replacement window handles made of upvc should be secure.

Measure the Spindle

If you need to replace a upvc window handle replacement handle that has collapsed, it's likely the spindle that holds it in place is damaged or is loose. In some instances, this could be fixed by using screws or pins to tighten it. In other cases it will require replacement completely. There are several kinds of window handles made of upvc. There are three types of handles: inline espagnolette, tilt-and-turn, and cockspur. Each handle type is installed and replaced in a different fashion.

Before you purchase a new handle, it's important to know the size of the one you have. This will ensure that the handle will fit the window correctly and will be of the correct size. Fortunately, all handles adhere to industry standards of sizing making it fairly easy to find the right size.

To determine the size of the handle move the window to the open position. You should be able to determine the dimensions of the pin or screw that secures the handle. Use a ruler or tape measure to determine the length the spindle is. Once you know the length of your spindle, it is possible to purchase a replacement that is the exact same length.

When you are looking to replace a handle you should take into consideration the step height of an window handle made of upvc. The step height is the distance from the base of the handle to the point at which it is placed on the frame. This usually is around 21mm or 9mm in aluminum and uPVC. Dropping objects into the gap will let you see how far the handle extends before it comes into contact with an obstruction.

Cockspur handles typically have different backset heights based on the style of window they are installed in. Inline espag handles have an average height of 43mm centre to centre (2 fixing points). Cockspur handles, however they have different backsets depending on the shape of the window they are in. This is because they have an extension spur that extends from the handle and locks over a cockspur wedge striker.

Fit the New Handle

After you have chosen the new handle, make sure it is aligned with the screw holes on the door. Then secure it using the screws provided. If you're also replacing the latch lever it can be put in similarly to the main sliding patio door handle replacement handle. Then, you can reattach the door trim to conceal the mounting screws and finish the project.

Tip: To remove a metal head from a wedge made of wood, place the handle on the floor so that its wide end is level with the ground. Then use an hammer and tap the narrow end. Be careful not to scratch the handle or the spindle.